IPMI Firmware Release Note ---------------------------- Filename: SMT_X9_331.bin version: 3.31 Date: 07/11/2014 1. [ X9DRFF-7G+/X9DRFF-TF+/X9DR3(i)-LN4+/X9DRG-HF/X9DRG-HF+/X9SRG/X9QR7-TF+/X9DRG-HTF-II ] Add support of K80 GPU 2. [Twin System, X9DRT-*] Add PUE Mode. 3. [ PCIe SSD ] i. Change wording of the Dis-locate to Stop Locate. ii. Fix always slot 0 HDD info 4. Change the feature that network setting is always preserved when fw update. 5. Fix the issue that iKVM connection is drop while doing installation of OS whose file size is more than 3GB or above. ====================================================================================== Filename: SMT_X9_330.bin version: 3.30 Date: 07/03/2014 1. [X9DRD-CT] Add back the standard mode in Fan Mode. ====================================================================================== Filename: SMT_X9_329.bin version: 3.29 Date: 06/23/2014 1. [WS-MAN] Fix the issue that user/password is not working correctly. 2. Improve function of OEM command of 0x30 0x90 to fix the SuperDoctor getting the wrong value. 3. Set BBP timeout shutdown featur default disabled. Note: The customer application/OS would trigger the graceful shutdown themselves by default. Validation: please plug in BBP along with power supplies, and make sure the shutdown won't be triggered by bmc in 30 seconds after all the power supplies failures happen ====================================================================================== Filename: SMT_X9_328.bin version: 3.28 Date: 06/05/2014 1. [SSL Certification] Add the SSL key & CERT mismatch detection while deploying new certification. Validation: a. upload mismatchd ssl key & cert, b. web should pop up error, SSL Certification failed..., and web server should be still working. 2. [Multi Node] i. Remove BP ID. ii. Display BP Revision starting from MCU Version of 1.06 and onward. 3. [Security] Improve the security protection on storage of root user account. Validation: a. Ensure the login is successfully as ADMIN user : i. after update the firmware. ii. after "Restore To Default" iii. after any change made to the root user account. ====================================================================================== Filename: SMT_X9_327.bin version: 3.27 Date: 05/23/2014 1. [X9DRD-CT+] Fix the fan control when PUE mode is being used. ====================================================================================== Filename: SMT_X9_326.bin version: 3.26 Date: 05/19/2014 1. [Multi Node with Twin System] Fix the issue that Node A incorrectly displalys Node B information. ====================================================================================== Filename: SMT_X9_325.bin version: 3.25 Date: 05/16/2014 1. [UDT with PWS-1K81P-1R] Add patch to fix the incorrect report from power supply about the power consumption. Validation: please verify power supply consumption reading through command raw 0x30 0xe2 0x0 0x0 0x0 2. [X9DRT-P] Fix the fan curve while using Xeon Phi. 3. Fix the Network Privilege settings. Validation: Please refer to SMT IPMI User manual. 4. [Multi Node] i. On Multi Node page, add BPN ID and BPN Revision data fields. The FRU page shall dispaly these same data fields as well. ii. [X9DRT-P] Fix the auto detection of Multi Node capabality. ====================================================================================== Filename: SMT_X9_324.bin version: 3.24 Date: 05/08/2014 1. [X9DRD-CT+] Set the correct fan mode per design request, i.e Heavy I/O, Full Speed, PUE mode. 2. [PCIe SSD] i. Improve detection of number of drive to display. ii. Add an ability to dynamically display PCIe SSD page based on the presence of SSD in the system. 3. [Multi Node] i. Add an ability to display Left/Right location based on Fat Twin MCU design. ii. Add highlight to background and wording in legend when block display is current node. iii. Correct the value of input current. 4. Fix http or https port number fails to change. Validation: Use 10000 as port number to check if https is working. 5 [X9DRG-HF/X9DRG-HF+/X9SRG/X9DRG-HTF-II] Fix the right/left zone fan curve when both zone are inserted with non reconized PCI cards. 6 Add wording(English) on PCIe SSD page and add Japanese wording in SMC RAKP/Power Consumption pages while using Japanese setting. ====================================================================================== Filename: SMT_X9_322.bin version: 3.22 Date: 03/21/2014 1. [X9SBAA] Disable Power Consumption page on web page. 2. [X9DRT_P] i. Add a feature of power monitoring on multi node. ii. Add GPU monitoring and its fan control. 3. Setting of Daylight Savting Time can be adjusted while using OEM Get/Set Config function. 4. [X9DB3-CPU_AI026] i. Make RT2 as a part of fan control. ii. Fix the reporting of DIMM location while ECC Error happens. iii. Remove Heavy I/O Mode. iv. Correct memory sensor in SDR. v. Add Fan 5 and Fa 6 in sensor monitoring. 5. Add feature of PCIe SSD monitoring. 6. [X9DBU] Add memory temperature sensor. 7. Fix the issues that values on BBP page are not able to save. 8. [X9SRD] Add support of memory monitoring. ====================================================================================== Filename: SMT_X9_321.bin version: 3.21 Date: 01-31-2014 1. [OOB] Fix the display of Activate BIOS Product Key. 2. [X9DRT-P] i. Fix the "video mode only in KVM" issue. ii. Fix the issue that event description is missing in the email alert when power failure happen. 3. [X9DB3-CPU] i. Fix the +5VSB, System and Peripheral Temp reading issues. ii. Set the LAN mode to Share LAN as default. 4. [X9DR7-LN4] Add the the support of high speed fan that is higher than 19K rpm. 5. [X9DBL] Correct sensor name to "P2-DIMMD1 Temp". 6. [X9DRG-OF] Fix the issue that fan speed control is not working while using Xeon Phi. 7. Fix the failure of login while using AD server that is configured to have longer length of user domain. 8. Fix Self-Signed Certificate works, and signed Certificate by CA. [Validation] i. Please use attachment certificate and key in SSL Upload. ii. Verify the upload is completed and the new certification reflects the new date. ====================================================================================== Filename: SMT_X9_320.bin version: 3.20 Date: 01-03-2014 1. Description: IPMI BMCs being abused for NTP amplification DDoS attacks NTP respond to all queries, so an attacker can potentially DDOS the IPMI by sending queries Affected functions: NTP function Validation Step: Run the follow command to see if any statistics reported from ipmi fw. ntpdc -c monlist 2. [X9DRG-OF] Add the patch for hardware workaround that avoid polling GPU Temp, and make the full speed mode always Full Speed while K10 is being used. 3. [X9DRT-P] Fix the issue that PUE mode is not default fan mode, and the PUE fan speed control. 4. [X9DB3-CPU-AI026] Add support of sensor monitoring. 5. [X9DRW-CF] Fix the Entity ID of SDR. Validation Step: a. Issue the command, ipmitool -H 172.31.16.112 -U ADMIN -P ADMIN sdr elist b. Verify all the return values in 4th column are unique. ====================================================================================== Filename: SMT_X9_319.bin version: 3.19 Date: 12-19-2013 1. [Release Note Revised on SMT_311]: # is allow. Fix the security issue: Don't allow inputing the special characters on the user name and password field. [Validation Steps] a. can't input the following characters on the user page(adding or modifying). ,; &'"<>\=$|^?*~`()[]{} 2. Fix the issue that SOL is not working over SMASH. [Validation Step] a. Login to SMASH, and launch SOL to check if SOL output is correctly display. b. exit the SMASH. c. Repeat Step a to Step b for 5 times, verify that SOL is working everytime. 3. Fix the issue that, when using I.E broswer, on Radius Web Page, the settings values are intermittenly missing. 4. Fix the issue that some valid character is not accepted on LDAP web page. 5. Add feature of SMC OEM RMCP, available on Miscellaneous->RAKP web page. [Validation] 1. Once RAKP on the web is enable, SMCIPMITool only can be used to run any IPMI command. [Note] SMCIPMITool 2.6.4 version with rakp set to on in SMCIPMItool.properties 2. Use ipmitool to run any IPMI command, none of the command can be run. 3. Turn the RAKP off, observe that ipmitool can be used. 6. [X9DRT-P] i. Correct VDIMM CD for SD. ii. Add PUE mode to fan control. 7. [X9DRW-7TPF+] Add Heavy I/O mode to fan control. 8. [X9DRW-CF] Enable feature of HDD monitoring. 9. [X9SBAA-f] Disable featur of OOB BIOS Update. 10. [X9DB3] Add memory sensor. 11. [OOB BIOS Update] Add bios revision when doing bios update through web and SMCIPMItool [Validation] (1) make sure the bios image can support bios revision. otherwise,it is not shown. (2) do bios update through web and SMCIpmitool. ====================================================================================== Filename: SMT_X9_318.bin version: 3.18 Date: 12-06-2013 1. Fix the security issue Don't allow inputing the special characters on the user name and password field. [validation steps] 1. can't input the following characters on the user page(adding or modifying). ,; &'"<>\=$|^?#*~`()[]{} 2. [GPU Boards] Add K6000 GPU Temp support. 2. 3. [X9DR6-LN4] Remove GPU from SDR, and initial constant fan speed mode as Full Speed once any GPU is preseted in the system. 4. [X9DRT-P] Correct pminfo result once any of power supply is unplugged. ====================================================================================== Filename: SMT_X9_317.bin version: 3.17 Date: 12-02-2013 1. [X9DRT-P] Fix IB/10G Temp issue. 2. [X9DRFF-i/7G] Add functionality that, For 6 GPU system, it uses power supply as a source of power consumption measurement. 3. Ehance security function on the web. Validation: Test all function on the web. ====================================================================================== Filename: SMT_X9_316.bin version: 3.16 Date: 11-15-2013 1. Dynamic SSL Key is generated. 2. [X9DRT-F/X9DRT-HF+/X9DRT-P/X9DRFF/X9DRFR/X9DRFF-7/iGP] Add 12V protection. 3. [X9DRT-P] Fix 10G and IB Temperature reading. ====================================================================================== Filename: SMT_X9_315.bin version: 3.15 Date: 10-31-2013 Fix the issue that ADMIN account cannot be loggeg in after the passwords have been changed a few times. [validation steps] 1. login to IPMI Web Gui->Configuration->User->Modify ADMIN 2. Change ADMIN pwd to ADMIN123 3. Check ipmitool remotely with new pwd ====================================================================================== Filename: SMT_X9_314.bin version: 3.14 Date: 10-30-2013 1. [X9DT-P] Add sensor monitoring, and Multi-PS support. 2. Add signed java certification to avoid Oracle blocking the java use in the future. 3. [X9DRG-OF] a. Add sensor support. b. Fix the temperature reading of GPU 7 and 8. c. Fix the optimal fan control. d. Add 10G SKU, and correct number of memory sensor. 4. [X9DBL] Add memory sensor monitor. 5. [X9DRG-HTF-II] Disable GPU Throttling triggered by B12 pin. 6. [X9DRFF-7GP] Add GPU monitroing support up to 6 GPU. 7. [X9DRD-EFUC] Correct the number of memory for sensor monitoring. 8 [X9DRW-CF] a. Display sensor as N/A when sensor polling priviledge is not avaiable to BMC. b. Remove HDD monitoring. c. 10G is a factor of fan control in I/O zone. 9. [X9DRL] Add memory sensor. 10. [X9DRD-LF] Change it to 6 FANs from 4 FANs in sensor monitoring ====================================================================================== Filename: SMT_X9_244.bin version: 2.44 Date: 10-21-2013 1. [X9DRW-CF] i. Display sensor as N/A when sensor polling priviledge is not avaiable to BMC. ii. Remove HDD monitoring. iii.10G is a factor of fan control in I/O zone. 2. [X9DRG-OF] Add sensor monitor and fan control for 8 GPU. 3. [X9DRL] Add memory sensor. 4. [X9DRD-LF] Change it to 6 FANs from 4 FANs in sensor monitoring ====================================================================================== Filename: SMT_X9_243.bin version: 2.43 Date: 10-11-2013 1. [X9SCE] Add PUE mode (default fan dutycycle as 0%) 2. [X9DT-P] Add sensor monitoring. 3. [X9DRG-HTF-II] Disable GPU Throttling triggered by B12 pin. 4. [X9DRFF-7GP] Add GPU monitroing support up to 6 GPU. 5. [X9DRD-EFUC] Correct the number of memory for sensor monitoring. 6. [OOB BIOS Update] i. Correct spelling mistake from Prouct to Product ii. Prevent the change of MAC address causing license lose. ====================================================================================== Filename: SMT_X9_242.bin version: 2.42 Date: 09-24-2013 1. [X9DRL-7F/EF] Fix dimm temperature sensors missing ====================================================================================== Filename: SMT_X9_241.bin version: 2.41 Date: 09-20-2013 1. [X9DRL-7F/EF] Add memory sensor monitoring. 2. Support OOB SMBIOS/Edit feature. Validation Requirement: Verify these OOB features: Fundamental, BIOS Update, BIOS Configuration/Setting, SMBIOS/DMI Edit. 3. [X9DRH/X9DR7-LN4] Fix the issue that UID is intermittenly lit up when power up the system. 4. Fix the heavy I/O mode not working well for single zone fan control. ====================================================================================== Filename: SMT_X9_240.bin version: 2.40 Date: 09-09-2013 1. Allow user to change ADMIN. Validation: i. Go to IPMI Web, Configuration -> Users. ii. Modify the ADMIn user, and check to see if the user name can be changed. iii.Once the name is changed successfully, try to use this account info for re-login. 2. [X9DRFF-7G+/X9DRFF-TF+/X9DR3(i)-LN4+/X9DRG-HF/X9DRG-HF+/X9SRG/X9QR7-TF+/X9DRG-HTF-II] Add GPU Temperature sensor monitoring of K40 GPU. 3. [X9DRW-CF31] Fix the hi/lo limit of 1.5V for SD. 4. Fix the issue that email alert is not working while using static IP mail server. 5. [X9SRW] Add monitoring of memory temperature sensor. ====================================================================================== Filename: SMT_X9_239.bin version: 2.39 Date: 08-19-2013 1. [X9DR6/i-F] Add CPU2 memory sensor. 2. [X9DRW-CT/CTF] Add HDD sensor. ====================================================================================== Filename: SMT_X9_238.bin version: 2.38 Date: 08-12-2013 1.[X9DRW-7TPF/X9DRW-7TPF+] Remove Heavy I/O fan mode. 2.[X9DR7-TF+] Add Heavy I/O fan mode. 3. Disable OOB feature for X9 Bromolow platform. ====================================================================================== Filename: SMT_X9_237.bin version: 2.37 Date: 07-30-2013 1. [X9DRD-LF/X9DRD-IF] Adjust fan, memory, and chassis intru sensor. 2. [X9DRX] Add HDD sensor monitoring. ====================================================================================== Filename: SMT_X9_236.bin version: 2.36 Date: 07-19-2013 1. Renew default SSL certificate from 7/17/2013 to 7/17/2014 2. [X9DRL-IF] Add patch to fix issue #46685, Board ID Mismatch. 3. [X9DRH] Add HDD Status Sensor. 4. [X9DRFR] Fix low limit of VDIMM GH. ====================================================================================== Filename: SMT_X9_235.bin version: 2.35 Date: 07-12-2013 1. [X9DRD-EF] Add memory temperature sensor. 2. [X9DR7-TF+] Fix the fan speed instable when doing stress test. 3. Fix the issue that IP Access Control on the web is not working. 4. [X9SRW] Fix the issue that VDIMM CD sensor is missing. 5. Add the extended LAN configuration to the presevation while doing restore to default. 6. [X9DRW-CF31/X9DRW-CTF31] Add sensor monitoring. ====================================================================================== Filename: SMT_X9_234.bin version: 2.34 Date: 07-05-2013 1. [X9DRFF-7G] Add noise filtering for fan present detection. 2. [OOB issue]fix the customer issue that the smbios may be lost after upgrading bios via ipmi. Validation : X9DRD-7LN4F a. BIOS X9DRD72.B21, boot to DOS and change SMBIOS string by amidedos. b. Flashing BIOS X9DRD72.C19 by OOB flash, after flashing, reboot system. c. Checking SMBIOS data, do all SMBIOS data preserve ? d. Repeat step 1 ~ 3 but exchange BIOS X9DRD72.B21 and BIOS X9DRD72.C19 3. [X9DRFR] Fix heavy mode I/O issue that fan control only takes place in single zone. 4. [X9DR6-F] Add memory support. 5. Change the calculation of power consumption based on AC Input Power. ====================================================================================== Filename: SMT_X9_233.bin version: 2.33 Date: 06-28-2013 1. Fix issue that email alert from ME is not needed. 2. [X9DRL-7F/EF] Fix the issue that hdd status monitoring is missing. 3. Fix issue that email alert from ME is not needed. 4. [X9DRW+] Add memory sensor. 5. [X9DRFR] Fix the fan control of Heavy I/O Mode. 6. [X9SRH] Remove non-critical log for fan failure. ====================================================================================== Filename: SMT_X9_232.bin version: 2.32 Date: 06-13-2013 1. [X9DRFR] Fix issue #45909, Update BIOS through IPMI web failed with Error message "BOARD ID mismatch". 2. Fix the issue that email alert is not working. ====================================================================================== Filename: SMT_X9_231.bin version: 2.31 Date: 06-12-2013 1. [X9DRL-7F] Correct the hi/lo limit of 1.1V sensor. 2. [X9DRG-HTF-II] Restore fan mode to user setting once the GPU temperature is recovered. 3. [X9SRL/X9SRH7] Add Memory VRM patch for hardware design. ====================================================================================== Filename: SMT_X9_230.bin version: 2.30 Date: 05-31-2013 1. [X9DRT-HTF+] Fix the low limit of VDIMM GH For SD3. 2. Support Delta Power Supply. Validation: Use Delta Made Power Supply such as PWS-1K66P-1R i. Check the Power Status in sensor monitor web page. ii. Check the error detection of Power Supply status. iii. Verify the reporting of power consumption. ====================================================================================== Filename: SMT_X9_229.bin version: 2.29 Date: 05-24-2013 1. Fix the display of Fixed Name as Fixed to ADMIN user. Validation: i. use ipmitool channel getaccess 1 2 ii. Verify that the field of "Fixed Name" is set to "Yes" 2. Fix the issue that email of SMTP sender is not shown in any alert email. Validation: i. Set sender email address in SMTP configuration page. ii. Send a test alert and verify the sender is match to the setting. 3. [X9DRD-EF-UC014] Remove UID LED. 4. [MB using 7904 HWM] Add Heavy I/O mode to Fan Mode Control. 5. [X9DRT-HF+] Fix the Fan 3 and Fan 4 sensor reading. ====================================================================================== Filename: SMT_X9_228.bin version: 2.28 Date: 05-16-2013 1. Correct DIMM alert string for SSM. 2. [X9DRG-HTF+-II & X9DRH-IF-NV] Add sensor support. 3.[X9DRD-EF-UC014] R: Disable Power Consumption page. 4.[OOB Update] Preserve the whole 64k block where SMIBIOS data resides. [Validation Steps] i. Go to the bios update page ii. Update bios image only with preserving SMBIOS. 5. [X9DBL-If/3F/6F] Fix the issue #45389 [BIOS ECO X9DBL3.502] Can't OOB updste BIOS. ====================================================================================== Filename: SMT_X9_227.bin version: 2.27 Date: 05-07-2013 1. [X9DRD-EF-UC104] Add sensor supoort. 2. [X9DRT-HF+] Fix the issue that VDIMM CD is missing in SSM. 3. Add OOB event log. OOB file build date mis-match (Sensor type : 0xCA, Event Data 1) OOB feature initial failure (Sensor type : 0xCA, Event Data 2) 4. [X9DAX] Remove non-critical event log of temperature. ====================================================================================== Filename: SMT_X9_226.bin version: 2.26 Date: 04-24-2013 1.Fix SMASH functionalities. 2.[BIOS OOB]enable web bios update by default. 3.[X9SCFF] Add default fan mode to PUE in FatTwin system, and fix PUE fan control. ====================================================================================== Filename: SMT_X9_225.bin version: 2.25 Date: 04-12-2013 1.Add new feature to BBP monitoring and feature of power monitoring. 2.Fix the issue the bios update with SMBIOS option failed by using smcibu. 3.[X9SCFF] Add PUE Fan Mode to FatTwin system. 4.[X9SRG] Correct fan curve of PWM of NVidia GPU. ====================================================================================== Filename: SMT_X9_224.bin version: 2.24 Date: 04-12-2013 1.[X9SRG] Add support of high speed fan. 2.[X9DRL-7F/EF] Add HDD monitoring. 3.Enable ME Alert event. 4.[X9DRD-7LN4F] Add HDD monitoring. 5.[X9SBAA] Remove non-critical event log generated by temperature sensor. 6.[X9SCFF] Swap RT1 and RT2 reading source. ====================================================================================== Filename: SMT_X9_223.bin version: 2.23 Date: 03-29-2013 1.[X9DRG-HF] Add support of high speed fan. 2.[X9SRG] a. Fix Issue ID=44684, KNC Reading cannot recover after IPMI cold reset. b. Disable KNC HW Trottle since the board doesn't support it ====================================================================================== Filename: SMT_X9_222.bin version: 2.22 Date: 03-22-2013 1. Allow NTP function configured through SMCIPMITool Validation: -1. java -jar SMCIPMITool.jar [IP] ADMIN ADMIN ipmi oem getcfg conf.txt -2. change NTP settings -3. java -jar SMCIPMITool.jar [IP] ADMIN ADMIN ipmi oem setcfg conf.txt 2. Fix system can't resume form C6 state when using iKVM 3. [X9SCFF] Fix identification of hadoop or fattwin system to prevent system reboot causing firmware cold reset 4. [X9QR7] Fix issue OOB BIOS update can't work 5. [X9DRW-7TPF+] Add Fan Optimal Mode 6. [X9SRL-F] Change Lower NC threshold as 3.136, and Upper NC threshold as 3.856 per hardware design 7. [X9DRFF7G+ Hadoop] Fix duplicated PS SDR 8. [X9DRFF7G+ FatTwin] Fix fan speed control can't work properly ====================================================================================== Filename: SMT_X9_221.bin version: 2.21 Date: 03-08-2013 1. Fix power control from SMASH Validation: 1. ssh [user_name]@[BMC_IP] 2. enter password 3. cd system1/pwrmgtsvc1 4. verify start/stop/reset function 2. [X9SBAA] Fix issue #44118, System freeze for ~10 minutes when "Detecting IPMI..." during cburn on/off stress test 3. [X9SCFF] - Support HDD status as onboard LSI RAID is configured - Fix issue #43385: display power supply status naming as "PS status" in 1U Hadoop System 4. [X9DRFF-7G+] - Remove chassis intrusion in FatTwin system - Add support for Hadoop or FatTwin system Note: FatTwin system comes with Hot-Swap controller from backplane 5. [X9DRFF-7G+/X9DRFF-TF+/X9DR3(i)-LN4+/X9DRG-HF/X9DRG-HF+/X9SRG/X9QR7-TF+] - Add K520 GPU support for fan control 6. [X9DRG-HF] Fix issue #44194, KNC Temperature reading cannot recover after IPMI factory default 7. [X9DRW-3LN4F+/X9DRW-3TF+] Disable event log for any non-ciritical threshold of temperature sensors per thermal guide ====================================================================================== Filename: SMT_X9_220.bin version: 2.20 Date: 03-01-2013 1. [X9DRG-HTF] a. Enable KNC HW Throttle on Board Revision 1.10 onward; Disable HW throttle on board before revision 1.10. b. Fix the CATERROR issue. 2. [X9SCFF] Improve detection of fattwin or hadoop system. Note: Must be paired with BIOS 3. [X9DRL-3F/iF] Combine the display of VDIMM EF and VDIMM GH to VDIMM EFGH 4. [X9DRFF7-G] Add 5V Standby sensor. 5. [X9DRL-7F] Change the display of FAN6 to FANA in sensor list. ====================================================================================== Filename: SMT_X9_219.bin version: 2.19 Date: 02-22-2013 1. [X9DRFF-7G+/X9DRFF-TF+/X9DR3(i)-LN4+/X9DRG-HF/X9DRG-HF+/X9SRG/X9QR7-TF+] (Board supporting Xeon Phi/GPU) Fix the issue that fans randomly go to full speed by improving better tracking the recover of I2C Read Failure. ====================================================================================== Filename: SMT_X9_218.bin version: 2.18 Date: 02-19-2013 1. [X9DRD-LF] a. Remove chassis intrusion and 4 fans from sensor monitoring. b. Fix Overheat buzzer doesn't work 2. [X9DRG-HF/HTF, X9DRG-HF+/HTF+] Increase NC threshold value of VBAT to 3.5. 3. [X9DRFF-7G+/X9DRFF-TF+/X9DR3(i)-LN4+/X9DRG-HF/X9DRG-HF+/X9SRG/X9QR7-TF+] (Board supporting Xeon Phi/GPU) a. Enable external throttle of Xeon Phi b. Change the deassert value of Xeon Phi HW throttling to 99 from 95 c. Add a feature that if any GPU/XeonPhi is present, BMC triggers FAN to full speed while during firmware update. 4. [X9DRL-3F/IF] Add VDIMM GH in sensor monitoring. 5. [X9DRL-7F/EF] a. Add sensor support for X9DRL-7F b. Add LSI HDD Storage Monitoring support 5. [X9SCFF] a. Add a feature to indentify FatTwin or Hadoop system. b. Remove AUX Temp in fat twin setup ====================================================================================== Filename: SMT_X9_217.bin version: 2.17 Date: 02-08-2013 1.[New Feature] Link Speed/Duplex can be configured manually through Web/OEM commands when Dedicated LAN mode is set OEM command format: NetFn:0x30/ CMD:0x70/ SubCMD:0x63 Set Link configuration (only for Dedicated LAN mode) Data 1: 0/1 [Get/Set] Data 2: 0 :Auto-neogitaion 1: 10M Half duplex 2: 10M Full duplex 3:100M Half duplex 4:100M Full duplex 2. [X9DRFF-7G+/X9DRFF-TF+/X9DR3(i)-LN4+/X9DRG-HF/X9DRG-HF+/X9SRG/X9QR7-TF+] (Board supporting Xeon Phi) - Add fan recovery when the status bit is clear or I2C failure is recovered - Add the event log when GPU throttling happens - Fix the fan randomly go to full speed - Add the auto detection of Xeon Phi slave address - Fix overflow of Xeon Phi temperature reading 3. [X9DRD-7] - After CATErr happens, add 20ms delay to check power ok to avoid false alarm - Disable event log of temperature sensors reaching Non-critical threshold per thermal guide 4. [X9DB3] - Enable CPU Overheat and Fan Fail LED using GPIOE7 - Fix Overheat buzzer doesn't work - Fix Sysmtem LAN3 MAC address can't displayed from Web GUI 5. [X9DRW-7TPF] Add HDD status to sensor list ====================================================================================== Filename: SMT_X9_216.bin version: 2.16 Date: 01-30-2013 1. Fix Power FRU Reading for DMI table. 2. [X9DRG-HTF+] i. Correct 10G threshold values. ii. Fix the issue the Left Zone of Fan Speed doesn't respond to temperature change. 3. [GPU Boards] Add support of K1 GPU card monitoring. 4. [X9DRT-F] Fix the IB Temp reading. 5. Add a feature to upload/download IPMI Configuration File in Text Mode. Note: Supported version of SMCIPMITool is needed. ====================================================================================== Filename: SMT_X9_215.bin version: 2.15 Date: 01-18-2013 1. [X9DRG-HTF+/X9DRFF-G+/X9DR7-TF+] Add a patch to instruct CPLD to disable GPU throttling. 2. [X9DRFF-7+] Add the ability to distinguish Fat Twin or Hadoop system. 3. [X9DR7-TF+] Add dynamic detection and loading of sensor monitoring based on new/old revision motherboard. 4. [GPU Boards] Add failure handler that triggers fan to full speed when KNC reports 0. 5. [OOB Update] Add PS OOB ====================================================================================== Filename: SMT_X9_214.bin version: 2.14 Date: 01-11-2013 1. Add dynamic display of storage page 2. [X9DR7-TF+] Fix FAN C display. 3. [X9DRFR] Fix HDD detection. ====================================================================================== Filename: SMT_X9_213.bin version: 2.13 Date: 01-04-2013 1. [X9DRFF-7G+] a. Fix the fan speed control. b. Take GPU account for NM Power Consumption c. Add the Chassis Intrusion. 2. [X9SCFF] a. Add chassis intrusion. b. Add an overall HDD sensor. c. HDD error asserted/de-asserted to SEL with slot information. 3. [X9DRD-LN4F, X9DRD-iF] Add memory temperature monitoring. ====================================================================================== Filename: SMT_X9_212.bin version: 2.12 Date: 12-28-2012 1. [X9DB3] Fix the issue 42087 2. [BIOS OOB]change wordings to "Product key" on BIOS update page. 3. [X9DR7-TF+] Add KNC reading. 4. [X9DRG-HTF+] Fix KNC GPU readings. ====================================================================================== Filename: SMT_X9_211.bin version: 2.11 Date: 12-12-2012 1. [X9DRH] Remove HDD monitoring feature. 2. [X9SRG/X9DRG-HTF/X9DRG-HTF+] Add K2 GPU Temp reading support. ====================================================================================== Filename: SMT_X9_210.bin version: 2.10 Date: 12-07-2012 1. Fix Swiss Keyboard can't be saved as input/physical keyboard layout; Note: Clear Java cache required. 2. [X9DRD] Version cut for OOB BIOS update. 3. [X9DR7-TF+] Add "Fan C" monitoring. 4. [X9DRW-7TFP+] Fix sensor polling function. 5. [X9DRG-HTF/X9DRG-HTF+/X9SRG] Add a feature that when any Kepler/KNC Temp reading is missing, the fan speed in that zone is set to Full Speed. ====================================================================================== Filename: SMT_X9_190.bin version: 1.90 Date: 12-04-2012 1. Add new board X9SBAA support ====================================================================================== Filename: SMT_X9_189.bin version: 1.89 Date: 11-28-2012 1. [X9SRW] Fix the missing sensor of FAN 5 on web 2. [OOB BIOS Update] a.Issue ID: 5271 smcibu, fix the below smcibu issues b.Issue ID: 41860, We cannot allow flashing BIOS and flashing IPMI fw simultaneously. c.Issue ID: 41861, IPMI needs to generate an event log when we activate the product. d.Issue ID: 41835, Flashing BIOS via webpage never finishes.(if doing retry, please wait 5-6 minutes) 3. [Storage Monitoring Feature] Issue ID: 42106, Fix the display of vendor name in Storage web page. 4. [X9DRH] Fix the monitoring function of HDD. ====================================================================================== Filename: SMT_X9_188.bin version: 1.88 Date: 11-20-2012 1. [X9DRW-7TF+] - Add the sensor reading of memory temperature - Add HDD support from I2C-1 2. [X9SCE/X9SCD/X9SRD(MicroCloud)] Correct Power supply status incorrect from command Validation: 1) Issue command "ipmitool sensor | grep PS" 2) check status is correct or not (0x1=> OK, 0x2=> Fail) 3. [X9DRH] Fix HDD sensor status and Storage Monitoring page unavailable Note: Storage Monitoring page is under IPMI Web-> Sever Health 4. [X9DB3] Add new board ID support 5. [X9DAX] fix the BIOS OOB issue Change BIOS configuration can't be successful. Validation Step: 1) Get BIOS current setting and save to USER_SETUP.txt ./smcibu -H 172.31.17.55 -U ADMIN -P ADMIN -c GetCurrentBiosCfgTextFile -f USER_SETUP.txt -O 2) Change BIOS setting in the file USER_SETUP.txt 3) Update BIOS setting ./smcibu -H 172.31.17.55 -U ADMIN -P ADMIN -c ChangeBiosCfg -f USER_SETUP.txt -R ====================================================================================== Filename: SMT_X9_187.bin version: 1.87 Date: 11-15-2012 1. Add a feature that LEDs are restored to off and Fans are restored back to setting when perform BMC cold reset. 2. [HDD Boards] -Improve stability of monitoring on HDD Storage features. -Fix spelling of "Raid Level Qualifier" -Enhance error detection mechanism. 3. [GPU Board] Add K20X GPU support 4. [X9DRFF-7+/X9DRFF-7G+] Add chassis intrusion sensor ====================================================================================== Filename: SMT_X9_186.bin version: 1.86 Date: 11-14-2012 1. Fix Fan Mode can't reset to default factory setting 2. Add power actions in iKVM Menu (including iKVM OSD menubar) Validation steps: 1. Please verify power actions working properly from iKVM menu 2. Please verify power actions working properly from iKVM OSD menubar 3. Fix Network settings can't be preserved after restoring IPMI configuration through IPMI Web 4. Fix the issue 'Unknown' is misspelled under Network Link Status 5. Add Battery Backup Power Monitoring page (excludes multi-node supported models, FatTwin) validatoin: 1. plug in BBP, 2. Please verify information under IPMI Web->Server Health-> BBP Monitoring 6. [X9DRT-HF/-HF+/-F(TWIN)] Remove multi-node support to fix conflict with BIOS doing re-driver 7. [X9DRG-HF, X9DRD, X9DRL, X9DRFF-7+, X9DRW-7TPF, X9DR3-LN4FP, X9DR3-F, X9DR7-TF+, X9DRH] - Fix logical HDD size problem - Add yellow warming for Rebuild status - Add space for the HDD event log between slot and enclosureID - Add partially degraded support 8. [X9DRFF-7+/X9DRFF-7G+] Fix fan fail LED can't be recovered when fan fail event deasserted 9. [X9DRW-7TPF+] Add new board support - Add sensor - Add HDD monitoring 10. [GPU Boards] Add NVidia K340 support 11. [X9DRG-HTF+] Fix sensor reading of Intel Xeon Phi 12. [X9SRL] Fix the fan mode selection display on web page 13. [X9SCE-F] Fix ECC error interpretation of DIMM location 14. [MicroCloud/Twin/FatTwin] Fix Input Current wording on Power Monitoring Page ====================================================================================== Filename: SMT_X9_185.bin version: 1.85 Date: 11-01-2012 1. [GPU] Add K20/Xeon Phi/ AMD Woodier GPU support 2. [X9SCE] Set default fan duty cycle at 65% to work around backplane issue 3. [X9DRG-HF, X9DRD, X9DRL, X9DRFF-7+, X9DRW-7TPF, X9DR3-LN4FP, X9DR3-F, X9DR7-TF+, X9DRH] Add features of LSI HDD support Validation: please verify information under Web GUI-> Server Health-> Storage Monitoring 4. [FatTwin/Twin] Fix BIOS can't Get Power Supply FRU for Multi-Node ====================================================================================== Filename: SMT_X9_184.bin version: 1.84 Date: 10-30-2012 1. Fix the Re-Drive functionality. ====================================================================================== Filename: SMT_X9_183.bin version: 1.83 Date: 10-30-2012 1. [X9DRH, X9DR7-LN4] Remove intermitten ON of UID after AC On. 2. Fix the fan/mouse mode settings can't be restored successfully using ipmicfg. 3. Fix the security issue that FW supports SSL Medium Strength Cipher Suites. 4. [X9SRG] Fix the fan control on right zone. 5. [X9DRFF] fix the VTT reading is not incorrect. 6. [X9SRD] Correct Entity ID/Instance for a part of VMware certification. ====================================================================================== Filename: SMT_X9_182.bin version: 1.82 Date: 10-25-2012 1. Fix the issue the dedicated LAN LEDs (Activity & Link LED) don't get blinking 2. Change the sender rule of Alert Email: - If DNS hostname is configured, it will be applied to sender email address; for example, [hostname]@X9ABC.com. - Otherwise, BMC MAC address will be assiged as default, Mac002590aabbcc@X9ABC.com (BMC MAC= 00:25:90:aa:bb:cc). (X9ABC is the model name) 3. Support BBP(Battery Back-up) sensor (Not supported for Twin/FatTwan) 4. [X9DR6/i-F] - Remove UID - Remove Non-Critical Event Log for Temperature Sensor per thermal guideline 5. [X9SCFF] - Rename VDIMM AB to V_DIMM - Adjust Hi/Lo Limits of VCC_PCH, VTT MEM, and 5VSB for SD3 6. [X9DRW-7TPF] - Remove Non-Critical Event Log for Temperature Sensor per thermal guideline - Remove Optimal Mode 7. [X9DRFF-7G+] Fix 12V Sensor Reading 8. On Power Monitoring Page(for boards supporting hot-swap controller), clarify the power consumption message by removing Input Power information ====================================================================================== Filename: SMT_X9_181.bin version: 1.81 Date: 10-11-2012 1. Correct system GUID for applicatioin(SD3/SMCIPMITool/IPMIView) to detect firmware vendor type 2. Workaround Power Support failure false alarm when PMBus is temporarily unavailable 3. Fix the issue the local system can't ping BMC Validation: plug in the lan cable to the dedicated and share port In Failover mode 1) ping BMC from the local system. 2) plug out either of lan cable and ping BMC. In Dedicated mode or share mode 1) ping BMC from the local system Finally, do reboot test and make sure BMC network is alive. 4. Improve web UI for the link status: grey out the link information on the network page when it's disabled 5. Fix SDR isn't updated with Preserve Configuration checkbox Unchecked after firmware flash Validation: 1. flash firmware through web, 2. check SDR is correct or not. 6. [X9SCD/X9SCE] - Fix CPU Temp Overheat can't be recovered - No CPU Temp Overheat event logs - Adjust de-rating for reading power consumption from LM25066 Validation: check power consumptioin from Web-> Server Health-> Power Monitoring page 7. [X9SCD/X9SCE] Support HDD status monitoring Validation: - Please check overall HDD status from Sensor list. - When error happens, please check SEL for HDD slot information. 8. [X9DBL] Fix the issue inlet temperature is not available for ME to read Validation: SMCIPMITool [IP] [Username] [Password] nm20 oemgettemp 9. Add support of GPU Temperature reading for SD3 10. [X9DRG-HTF+] - Add Fan G and Fan H sensor support - Support high speed fan 11. [X9DRFF-7+] - Fix 10G Temp reading - Remove 1.5V sensor monitoring 12. [X9DRFF-7G+] Fix Sensor Monitoring 13. [TWIN] Fix PS status can't report correct status with multi-node BPN installed 14. [FatTwin] Enable Power Monitoring page under System Health ====================================================================================== Filename: SMT_X9_180.bin version: 1.80 Date: 09-28-2012 1. [X9DRFF] Increase VBAT threshold to 3.552V. 2. [X9DRW-7TF+] Add memory sensor. 3. [X9DRFF-7G+] Add sensor support. 4. [X9DRFF-7+] a. Add PUE fan control mode. b. Increase VBAT threshold to 3.552V. c. Add Fan9 and Fan 10, and correct the range of 5V STB 5. [X9DRG-HTF] Support 6 GPU reading. 6. Adjust GPU threshold value and Fan Control Curve for KNC. 7. Update the 0x34 GPU command. 8. [X9DRG-HTF+] Add K10 support. 9. Add network link status information on network web page. 10 Add sub oem command, "Get Network Link Status" (0x30, Cmd: 0x70, Subcmd: 0x60) 11. Fix power supply failure false alarm during production eburn test Note: Power supply failure false alarm comes from I2C errors Solution: Don't log the event until 3-times errors in a row 12. [TWIN/X9DRT] Add power supply multi-master support. 13. [X9DRD-LN4+] ADD Memory temperature present on IPMI web page. 14. Modify the Japanese wordings on Java IKVM viewer. 15. Solve X9SRH-7 issue,"FAN A speed is incorrect when set FAN to Standard Speed". ====================================================================================== Filename: SMT_X9_179.bin version: 1.79 Date: 09-11-2012 1. [X9DRG-HTF+] a. Adjust fan control. b. Fix the fan mode setting. c. Remove Fan G and H, and GPU3 and GPU4 Temp. 2. [X9DRG-HTF+/X9DRG-HF] Add Intel KNC GPU reading. 3. [X9DRW_7TPF] a. Correct sensor name FanA as Fan6, b. Correct Fan mode selection as Standard and Full speed mode 4. Fix LAN Mode unable to Get from OEM command Validation: LAN mode get: Input : NetFn 0x30 Cmd 0x70 Param1 0x0c Param2 0 [read] Output: Completion Code 0x00 Data [dedicated/onBoard/failover] 5. [X9QR7-TF] Fix screen will freeze when doing IPMI coldreset test. 6. [X9SCE-F] Add sensor support 7. [X9SRG] Add Kepler GPU support. 8. [X9SRL_CF] a. Add fan control b. Solve issue 39460, fans doesn't full swing on overheated memory ====================================================================================== Filename: SMT_X9_178.bin version: 1.78 Date: 08-30-2012 1. Fix Fan mode selection unavailable from IPMI Web 2. [X9DRFR] Change upper thresholds of VBAT sensor to 3.552/3.696/3.84 (UNC/UC/UNR) ====================================================================================== Filename: SMT_X9_177.bin version: 1.77 Date: 08-28-2012 1. Fix 10Gb LAN speed cannot be detected from Windos (IssueID: 39947) Validation: Device Manager --> Network Adapters --> LAN Properties --> LAN Speed 2. [X9DRFR/X9DRFF/X9DRFF-7+] Support Multi-Node power supply status monitoring 3. [X9DRFF-7+/i+, X9SCFF, and X9SRD-CF] Add sensor support, and Fan Speed Control 4. [X9DRT/X9DRT-F/X9DRT-IBFF/X9DRT-IQFF] Add memory sensors 5. [X9SRL-CF] Fix No FanA sensor reading item in IPMI web (IssueID: 38788) 6. [X9SRI] Correct the legth of PCH Temp sensor in SDR for VMWare certification ====================================================================================== Filename: SMT_X9_176.bin version: 1.76 Date: 08-16-2012 1. Fix issue when one of CPUs de-assertion happens, FP LED and BEEP restore back to normal state 2. Fix SOL can't work over SMASH Validation Steps: a. SSH login to BMC b. Once at command prompt, cd system1/sol1 c. Issue command: start 3. [X9SCFF, X9DRW-7TPF] Add sensor support 4. [X9SRH] - Fix FAN Failure function not working (IssueID: 39678) - Fix FP LED not blinking when fan fail and power fail happens (IssueID: 39478) Note: System reset required 5. [X9SCD-F/-HF R1.10] Support HDD1/2 Status for R1.10 and backward compatibility Note: Board rev info supported by BIOS is required 6. [X9SCD-F/-HF, X9SRD] Monitor Power Status from PWRFAIL-_SENSE (GPIOE3) ====================================================================================== Filename: SMT_X9_175.bin version: 1.75 Date: 08-10-2012 1. Fix CPU Overheat LED/Beep is on after Thermal Trip de-assert 2. Add reset to default command with FRU/LAN setting erased Validation: IPMICFG -fde or IPMICFG -raw 30 41 3. [X9DRT7-TF+] - Add GPU support - Add memory sensor 4. [X9QR7-TF] - Add Kepler GPU support 5. [X9SRH7] - Fix ¡§IPMI Sensor reading no "CPU Temp" (IssueID: 39676) - Add PCH sensor - Add FAN Hi/Lo limit 6. [X9DRT-IBFF] - Fix IPMI sensor did not have VDIMM EFGH (IssueID: 39377) Note: Reset to default required 7. [X9SCD] Fix CPU Temp reports "Not Present" when temp stays in the range of "Low" ====================================================================================== Filename: SMT_X9_174.bin version: 1.74 Date: 08-06-2012 1. Improvements on Power Supply status monitoring: - Fix power failure LED stopped blinking when system is still in power failure state (IssueID: 39575) - Fix power supply wrong index (IssueID: 39513, 39511) - Improve on power failure detection (IssueID: 39469) - When power supply module being removed or unreachable through I2C, status shows "Not present or Failure detected" from IPMI Web - Support get power supply individual status(0x30 0x9D) for SD3 2. Fix "Can't Login" issue when using Active Directory over SSL 3. Fix VLAN issue IP may sometimes be gone after setting up VLAN 4. [X9DRFR/X9DRFF] Fix the event log of fan fail 5. [X9DR3-LN4+] Add GPU support for Revision of Board 1.20 Note: compatible BIOS required 6. [X9DR7-TF+] Change Slave Address of HWM to 0x5A ====================================================================================== Filename: SMT_X9_173.bin version: 1.73 Date: 07-26-2012 SVN: 797 1.Support Swiss Keyboard 2.Skip Hotkey F4 in the hotkeys settings of preference menu tab. NOTE: IKVM version increases as 1.69.14 If the user configured hotkeys before, please click "Default" button to load new default hotkeys. 3. Fix Japanese Keyboard can't take "_" key 4.[X9DRFF, X9DRFR] a. Remove chassis intrustion. b. Remove non-critical event log of memory temperature. 5.[X9DRG-HF] a. Add Kepler GPU support. 6.[X9SRH7] Add sensor support, and Fan Mode Control. 7.[X9QR7-TF] a. Adjust Fan Speed Control Zone. b. Remove PCH Temp from Fan Control. c. Fix 10G sensor. ====================================================================================== Filename: SMT_X9_172.bin version: 1.72 Date: 07-20-2012 SVN: 755 1. Improve on Power Supply status monitoring - Support PWS721P Power Supply status monitoring - Log Power Supply failure events when 3-times errors in a row 2. Fix Unit Reset cannot redirect to login page (IssueID: 38449) ====================================================================================== Filename: SMT_X9_171.bin version: 1.71 Date: 07-18-2012 SVN: 741 1. Fix intermittent report of Power Supply Failure. 2. Fix the IE8 compatibility issue that the display of Fan mode is missing 3. [X9QR7-TF] Fix matching slot number for GPU idetification. 4. [X9DRT-F] Remove FAN2 sensor. 5. Provide command access to Power Supply FRU. ====================================================================================== Filename: SMT_X9_170.bin ver1.70 Date: 07-13-2012 1. [X9DR3-LN4+, X9DR7-TF+, X9QR7-TF, X9DRG_HTF+] Fix issue BMC initialization failed when plugging 2 or more power supplies 2. Fix User with privilege "No Access" can't be configured correctly from IPMI Web Validation: Please check user privilege by command, ipmitool -I lanplus -H [IPMI-IP] -U ADMIN -P ADMIN user list 3. [X9SRE-DS018] Fix memory reports event logs when reading is not available (memory throttling disabled) 4. [X9DRL-3F] Fix CPU2 VCore/VSA reports reading/event when only CPU1 is installed 5. [X9DRT-HF+] Add 12V Protection feature 6. [X9QR7-TF] Change slave address of HWM to 0x5A 7. [X9DRT-HF] Fix CPU Temp shows N/A from IPMI Web 8. [X9DRG-HTF+] Add CPU Temp reading in celsius degree ====================================================================================== Filename: SMT_X9_169.bin ver1.69 Date: 06-29-2012 1. Fix DOS firmware update tool, dUpdate, can't preserve network settings Validation: issue command, "dUpdate -f SMT_X9_169.bin -r n", and verify if network setting are preserved 2. Detect power supply dynamically Note: Support SMC power supply, standard power supply and the power supply connected to ME 1) SMC power supply which followed PMbus Spec (slave address: 0x78 , 0x7a , 0x7c, and 0x7e) 2) SMC old power supply (slave address: 0x70 , 0x72 , 0x74, and 0x76) 3) Standard power supply (slave address: 0xb0, 0xb2, 0xb4, and 0xb6) 4) power supply connected to ME, not BMC 3. Filter unknown event logs from Windows with OEM event type: 0xDE 4. [Romley Platform] Display CPU Temperature in Celcius degree 5. [X9SRE-DS018] - Add memory temperature monitoring - Remove fan Optimal Mode selection from IPMI Web 6. [X9QR7-TF] - Adjust PWM of fan speed control - Add buzzer sound when overheat - Fix the sensor display on non-10G board. 7. [X9DAX] Fix LED control when power fail/fan fail/overheat. 8. [X9DRD/X9DBL] - Add buzzer sound when overheat - Add JOH1 LED control (Note: Setting from BIOS Needed for X9DBL-iF/3F V1.02, X9DRD-iF V1.03) 9. [X9SRG/X9DRG] Add memory temperature monitoring 10. [X9SRL] Increase VSB NC threshold value 11. [X9DRG-HTF+] - Enable fan seep mode setting from IPMI Web - Add memory temperature monitoring 12. [X9SPU] NMI triggered by GPIO9 per hardware design ====================================================================================== Filename: SMT_X9_168.bin ver1.68 Date: 06-19-2012 1. Output GPIO7 as Open Drain when Overheat occurs, except for X9DBL, X9DBU, X9DR7-LN4F, X9DRD-iF, X9DRD-7LN4F, and X9SRE-DS018 2. [X9DRD-iF, X9DRD-7LN4F, X9DRF-R, X9DRF-F] Support Fan Power Utilization Effectiveness(PUE) Mode 3. [X9DR7-TF+/X9DR3_LN4+] Display CPU Temp in celcius degree 4. [X9DRW-7TFP] Add sensor support 5. [X9SRG/X9DRG] - Fix PWM control when there is no GPU card in slots - Fix PWM of zone control when there is non-GPU card in slots Note: Need BIOS integration 6. [X9DRFR] - Adjust Hi/Lo Limits for SDIII - Correct location of memory reading - Add the fan speed mode - Fix CPU Temp in negative value 7. [X9SRE-DS108] - Fix 1.1V, 5V, and RT2 readings - Add blinking funtion of UID ====================================================================================== Filename: SMT_X9_167.bin ver1.67 Date: 06-01-2012 1. [X9DRFF] Add sensor support, and fan speed mode control 2. [X9QR7-TF] - Adjust fan mode of fan speed control, and add GPU Temp reading - Correct calculation of VCORE2 and System Temperature reading 3. [X9DRFR] - Add CPU and memory reading in degree C - Remove FANB reading. 4. [X9DR7-RF+] Remove 1.5V sensor 5. [X9SPV] Correct PCH Temperature reading 6. Remove PROC_HOT CPLD event because it's duplicated from CPU Overheat event ====================================================================================== Filename: SMT_X9_166.bin ver1.66 Date: 05-24-2012 1. Preserve Network settings when Factory Default is executed 2. Fix Clear Chssis Intrustion can't work intermittently 3. [X9SPV] - Support PCH Reading - Swap FAN2 and FAN4 reading - Enable front panel LED for fan/power fails 4. [X9SRD] Add power monitoring from hot-swap controller, LM25066 Validation: IPMI Web-> Miscellaneous-> Power Monitoring ====================================================================================== Filename: SMT_X9_165.bin ver1.65 Date: 05-16-2012 1. Fix video messup issue during firmware cold reset 2. In FSC Optimal mode, fix FAN(in Zone2) set to full speed when CPU Overheat happens 3. Fix OEM Command for SD3 to read CPU Temp 4. Correct Entity ID for VMWare Certification 5. [X9DBL/X9DBU/X9SCV] Correct ECC Error DIMM location interpretation 6. [X9QR7-TF+] - Fix the fan naming - Fix Fan6 and Fan7 reading - Fixed fan position, VDIMM naming, and add Lan Temp 7. [X9SCV] Add high/low limit for SD3 8. [X9DRD_LN4] Fix the sensor number of VDIMM 9. [X9DBL] - Fix Fan Speed Control funcion - Fix PCH sensor reading 10. [X9DR7-TF+] - Adjust high/low limit of 10G Temp - Change the name from "LAN Temp" to "10G Temp" 11. [X9SRD] Remove chassis intrusion per Hardware Design ====================================================================================== Filename: SMT_X9_164.bin ver1.64 Date: 05-08-2012 1. Fix CPU/PCH Temp reading shows not available sometimes 2. [X9SPU/X9SCL/X9SCM] Add Fan Speed Mode control in IPMI Web-> Configuration-> Fan Mode 3. [X9SCD/X9SCM/X9SPU/X9SRD/X9SRI] - Correct threshold of System and Peripheral Temp - Correct fan speed calculation - Ignore NC event log of FAN per Thermal guideline 4. [X9SCM] Add sensor of Peripheral Temp 5. [X9SRD] Fix Vcore sensor reading ====================================================================================== Filename: SMT_X9_163.bin ver1.63 Date: 05-04-2012 1. Operator can't lauch IPMI Web-> Remote Control-> SOL Console 2. [X9DR7-TF] Adjust high/low limit for SuperDoctor III 3. [X9DBL] 1. Fix the -12V reading 2. Correct the System and Peripheral Temperature reading 4. [X9SCM, X9SCL, X9SCA, X9SCM_II, X9SCD, X9SPU] - Fix ECC Error DIMM interpretation for UP Bromolow 5. [X9QR7-TF] 1. Change the fan name per silk screen 2. Adjust Vcore3 reading calculation 3. Add 5V sensor 6. [X9DRT-HF] Prevent system on after 12V protection is triggered ====================================================================================== Filename: SMT_X9_162.bin ver1.62 Date: 04-27-2012 1. [X9SPU-F] Change the naming of FANA to FAN5 2. [X9SCA] Add fan mode menu under IPMI Web-> Configuration 3. [X9DR7-LN4F] Adjust high/low limit for SDIII 4. Fix BMC responded busy when the first AC on ====================================================================================== Filename: SMT_X9_161.bin ver1.61 Date: 04-26-2012 1. Add new board X9QR7-TF support - Update high/low limit for SD3 2. Add new board X9DR7-TF+ support 3. Add new board X9SRE-DS108 support 4. [X9DRT-HF] Add 12V protection feature 5. [X9DR7-LN4F] Fix 1.1V reading 6. Fix the incorrect SEL time 7. Fix IPMI Web SOL Authentication error with newly created users 8. Fix ProcHot events filled up SEL list 9. Fix Dedicated LAN ustable issue by adjusting PHY setup time ====================================================================================== Filename: SMT_X9_160.bin ver1.60 Date: 04-18-2012 1. Add new board X9DRT-F support 2. Add new board X9DAX support 3. [X9QR7/X9DRT-F] Add Fan Mode support from IPMI Web Validation: IPMIWeb-> Configuration-> Fan Mode 4. [X9SCM_II] Support NMI handler by GPIOE9 5. [X9SCM_II] Fix FanA always runs at full speed 6. [X9SPV] Add CPU Temp reading from HWM NCT6776F 7. [X9SPV] Support Fan Speed Control 8. [X9SCV/X9SCM_II] Adjust the upper threshold System and Peripheral Temp per Thermal guide 9. [X9DRX] Fix BMC dedicated LAN stop working issue 10. Intepret PCI Errors from Email Alert ====================================================================================== Filename: SMT_X9_159.bin ver1.59 Date: 04-12-2012 1. Fix SOL unable to launch by JDK security method Validation: IPMI Web-> Remote Control-> SOL 2. [X9DBL] Enabled Power Fail LED ====================================================================================== Filename: SMT_X9_158.bin ver1.58 Date: 04-11-2012 1. Prevent clock change during firmware cold reset Validation: 1. AC on/off test, and 2. cold reset test 2. Fix SOL fails to launch by cipher 1 authentication 3. Fix AD Server authentication fail 4. Intel Romley platform Package State is unable to enter the C6 state, stay in C2 state The solution: Virtual USB1.1 enters suspend mode and wake up the system by the remote Keyboard/mouse Validation: 1. boot windows 2008 Server SP1 x64 2. Run utility 3. check Package State 4. Package State more than 85% Pass 5. Renew SSL certificate, validated from 04/11/12 to 04/11/14 Validation: IPMI Web-> Configuration-> SSL Certification 6. [X9SCM_II/X9SCA/X9SCD] Enabled CPU overheat beep 7. [X9SRL] Remove FAN5 from sensor list 8. [X9SPV] Correct High/Low limit of Pheripheral Temperature for SD3 ====================================================================================== Filename: SMT_X9_157.bin ver1.57 Date: 04-05-2012 1. Fix security issue: IPMIv2.0 Cipher 0 Authentication(no password) is not allowed Validation: User can't log in BMC from commands with parameters "-I lanplus -C 0" Example: ipmitool -I lanplus -C 0 -U ADMIN mc info 2. [X9DRT-HF+] Adjust High/Low limits of "VDIMM CD" 3. [X9SCV/X9SPV] Correct VCCSA Reading ====================================================================================== Filename: SMT_X9_156.bin ver1.56 Date: 04-02-2012 1. Fix SPI clock issue with new bootloader Note: AC cycle required 2. Support logs of Web Administration at IPMI Web Maintenance -> System Event log Note: User log in/out & KVM log in/out status will be maintained. ====================================================================================== Filename: SMT_X9_155.bin ver1.55 Date: 03-29-2012 1. Fix System informatioin missing from IPMI Web 2. [X9DRT] PECI disabled from HWM NCT7904D per hardware design Note: AC cycle required. 3. [X9DRT-HF+] Enable Fan Mode from IPMI Web ====================================================================================== Filename: SMT_X9_154.bin ver1.54 Date: 03-27-2012 1. Add new board X9DRT_HF+ support 2. Add new board X9DR7_LN4F support 3. Correct ECC Error intepretation for X9 design 4. Fix Gateway IP reset to 0 whenever subnet mask changes 5. Correct IPMI Event ID match with SEL record ID 6. [X9SCM_II] Enable Fan Mode from IPMI Web ====================================================================================== Filename: SMT_X9_153.bin ver1.53 Date: 03-16-2012 1. [X9DBU] Fix PCH Temp missing in the sensor list 2. [X9SRG] Fix GPU1/2 Temp are missing in the sensor list 3. [X9SRG/X9DRG]Enable slowdown and shutdown GPU Note: This is the procedure mentioned by X9DRG and X9SRG Thermal Guideline. To validate the slow down and shutdown functions, it is recommended to heat up the card with a hair dryer. Please see Figure 5 (Page 12) for slow down and shut down signal locations. The original 3.3V signal goes to 0V when it reaches the temperature threshold (slowdown at 91oC, shutdown at 96oC). ====================================================================================== Filename: SMT_X9_152.bin ver1.52 Date: 03-12-2012 *** Note: Factory Default required *** 1. Adjust Fan Speed reading formula and thresholds for boards using NCT7904D 2. [X9DRW_LN4+] Adjust VCORE upper thresholds as 1.488(UNC), 1.52(UC) & 1.552(UNR) 3. [X9QR7] Remove one extra entry of CPU4 Temp 4. [X9DBU] Add PCH Temp sensor monitoring 5. [X9DRH] Adjust High/Low limit of LAN Temperature 6. [X9SRG] Add GPU1/GPU2 Temp reading and Fan Speed Control 7. [X9DRG] Adjust PWM for Fan Speed Control 8. [X9DRG] Change the GPU Temp upper thresholds as 85(UNC), 90(UC), and 95(UNR) ====================================================================================== Filename: SMT_X9_151.bin ver1.51 Date: 03-01-2012 1. Fix CPU Overheat threshold as DTS/PECI reaches up to -2 2. [X9DRD] Adjusted Fan Speed Control - Duty cycle at initial state down to 10%, and - Full speed as DTS up to -5, intead of -10 3. [X9DR3-LN4+] Allow PROCHOT_P0/1_N and THERMTRIP_P0/1_N event triggered by GPIO Interrupts 4. [X9DRT] Fix IB Temp reading missing 5. [X9DRG] Fix GPU tempereature reading 6. Add new motherboard X9SPU support ====================================================================================== Filename: SMT_X9_150.bin ver1.50 Date: 02-24-2012 1. Correct Fan Speed formula for board using HWM NCT7904D 2. [X9DRF] Support Fan Speed Control through PWM1/PWM2 3. Improved on IPMI SEL circular buffer for Total Event and Maximum Record ID Validation: 1. If the total event is over 512, it will delete 1 event and add 1 event, so the total event is always 512 2. The SEL record ID will reach until 65535 then go back to 1 (ipmitool sel elist) 4. Correct sensor length of CPU Temp Validation: Issue "ipmitool sensor list" and check if "CPU Temp" is displayed correctly ====================================================================================== Filename: SMT_X9_149.bin ver1.49 Date: 02-17-2012 1. [X9DRT-HF+] Support sensor reading & power monitoring from Hotswap controller ADM1276 *** AC cycle required 2. Improve Fan Speed reading accuracy 3. Add new motherboard X9DRF support 4. [X9QR7] Correct CPU3/4 Temp reading 5. [X9DRG] Matching slot number given by BIOS to support GPU Temp reading 6. [X9DRG] Fix Fan reading unstable issue (IssueID: 34927) ====================================================================================== Filename: SMT_X9_148.bin ver1.48 Date: 02-09-2012 1. Add new motherboard X9QR7 support 2. [X9DRH] Remove 1.1V and 15.V reading per design 3. [X9DRG] Fix FAN Limit for SD3 4. [X9DRG, X9DRW, X9DRH] Support 10G Temp reading 5. [X9DRT] Support Infiniband Temp reading 6. [X9DRT-HF] Support power monitoring from HotSwap Controller, ADM1275 *** AC cycle required 7. Fix CPU Overheat LED for motherboard using HWM NCT6776F ====================================================================================== Filename: SMT_X9_147.bin ver1.47 Date: 02-02-2012 1. [X9D_] Correct Fan Control table for mb using HWM NCT7904D 2. [X9DRT] Fix SOL issue as SP1 to SI2 config enabled 3. Disable PMBUS_ALERT from CPLD Validation: 1. Use redundancy PWS, latest BIOS, IPMI FW 1.46, WS2008R2 SP1, & latest Intel PTU 2. Pull out 1 PWS module and trigger a power failed condition ¡V Make sure PTU report PROCHOT# assertion 3. Put PWS back to normal condition, and upgrade IPMI FW to attached one, FW 1.47beta 4. Pull out 1 PWS module and trigger a power failed condition ¡V Make sure PTU DOES NOT report PROCHOT# assertion 4. [X9SRW/X9SRL/X9SRG] Support OEM Commands for BIOS to set Soft Watchdog Timer ====================================================================================== Filename: SMT_X9_146.bin ver1.46 Date: 01-26-2012 1. [X9SRI/E] Enable fault LED indicator as CPU Overheat, Fan Fail, or Power Fail occurs 2. Filter out events logged from ME with OEM Record Type 0xdd (IssueID: 33609) 3. Log power supply failure when consecutive twice errors in a raw to prevent false alarm (IssueID: 33263) 4. [X9DRT] Enable SP1 to SI2 config for COM port setting Validation: 1) SOL and 2) COM port ====================================================================================== Filename: SMT_X9_145.bin ver1.45 Date: 01-19-2012 1. [X9SPV, X9SRD] Add fan control page 2. [X9DBU] Fix 5VSB sensor reading 3. [X9DRD_7LN4] Allow interrupt to log CPLD events 4. CPU Temp reading caculated from TjMax and adjust the threshold per thermal guide 5. Support OS Boot/Stop description from Alert Email (IssueID=122321) ====================================================================================== Filename: SMT_X9_144.bin ver1.44 Date: 01-10-2012 1. [X9DR6-LN4F] Allow interrupt to log CPLD events 2. [X9SRW] Fix Fan4 missing issue 3. [X9SRD, X9DBL, X9DRD-7LN4F] Support sensor status reporting ====================================================================================== Filename: SMT_X9_143.bin ver1.43 Date: 01-05-2012 1. [X9DBU] Fix Power Fail LED not working (IssueID=32913) 2. [X9DRD] Fix COM2 not working with Rev1.42 Validation: 1. Connect null modem cable between X9DRD MB and your computer 2. Enter X9DRD BIOS Setup and change Advanced -> SIO Configuration -> Serial Port 2 Configuration -> Serial Port 2 Attribute item to COM 3. Run HyperTerminal on your computer 4. POST information in HyperTerminal 3. [X9DRG] Fix NMI can't be triggered (ProjectID=4290) Validation: ipmitool -H [bmc-ip] -U ADMIN -P ADMIN power diag 4. [X9DRG] Corrected PWM setting for FSC (IssueID: 31355) 5. [X9DRG] Fix ECC Error Event discription from Alert Email (IssueID=34138) ====================================================================================== Filename: SMT_X9_142.bin ver1.42 Date: 12-22-2011 1. Fix sensor reading unstable issue for board using NCT6776F (IssueID: 33138; FANA is always reading larger) 2. [X9DRW_LN4+] Fix the missing sensor of 5VSB 3. [X9SCM/L, X9SCA/I, X9SCD, X9SRI, X9SRL, X9SCV] Correct lower threshold of Vcore sensor for board using NCT6776F Note: 0.48(LNR) 0.512(LC) 0.544(LNC) 4. [X9SRI, X9SRL, X9SRW] Add PCH Temp sensor 5. [X9DRL, X9DRG] Fix CPU2 Overheat false alarm (IssueID=33795) ====================================================================================== Filename: SMT_X9_141.bin ver1.41 Date: 12-16-2011 1. Correct formula of Vcore reading (IssueID=33791) 2. [X9SRI/E] Fix Fan Mode selection hidden from IPMI Web 3. [X9DRG] Fix uninstalled fan reports reading 4. [X9DRL] Fix false alarm of CPU Overheat ====================================================================================== Filename: SMT_X9_140.bin ver1.40 Date: 12-14-2011 1. Support X9SRL board 2. Support X9SCV board 3. Support X9DRD-7LN4F board 4. [X9SRW] Add Fan4 for V1.01 board 5. [X9SRI/E] HWM NCT6776F Configuration 6. [X9SRI/E] Add Fan Mode Selection (Issue ID: 32711 and #33018) 7. [X9SRI/E] Fix OEM command for SD3 to read sensors (Issue ID: 33304 and 33054) 8. [X9DBU] Set high/low limits in HWM NCT7904D for applications 9. [X9DRT, X9DRT_SG] Adjust de-rating for reading power consumption from LM25066 10. Fix Fan Mode Seletion hidden from IPMI Web 11. Fix CPU2 reports "Not Present" when Overheat triggered ====================================================================================== Filename: SMT_X9_139.bin ver1.39 Date: 12-06-2011 1. Support OEM command to get PCH Temp: raw 0x30 0x95 2. Remove un-supported Fan Mode from IPMI Web 3. Log CPU overheat event as error occurs 3 times in a row Note: Avoid false alarm 4. [X9DRX] Correct Fan speed reading offset of FAN1,2 & 6 5. [X9DRX] Support OEM Command to set/get BIOS version & release date 6. [HWM NCT7904D] Correct VCore threshold in HWM NCT7904D for SD2, SD3, etc Note: AC Cycle Required 7. [HWM NCT7904D] Patch Chassis Intrusion status monitoring for HWM NCT7904D A4 chip Note: Chassis Intrusion status is latched in HWM NCT7904D A4 version, but read-clear in A2. Validation: In A4 chip, to clear chassis intrusion, user has to click on "reset chassis intrusion" button from IPMI Web. 8. Fix set user privilege command through KCS Validation: 1. Create a new user by the below command flow: ipmitool user set name [id] [name] ipmitool user set password [id] [password] ipmitool user enable [id] ipmitool user priv [id] [priv] 1 ipmitool channel setaccess 1 [id] callin=on ipmi=on link=on privilege=[priv] 2. Log into IPMI web and check if privilege complaint with features ====================================================================================== Filename: SMT_X9_138.bin ver1.38 Date: 12-01-2011 1. [X9DRT] correct de-rating value to support power consumption from LM25066 2. [X9SRD, X9DRD_LN4] add board ID support 3. [X9DR_] Remove PCH Init from HWM NCT7904D Init Note: PCH will be read from ME (SMLink0) Validation: AC Cycle required after firmware update 4. [X9DRG] Correct Fan Speed Control source mapping ====================================================================================== Filename: SMT_X9_137.bin ver1.37 Date: 11-29-2011 1. [X9DRD] - Configure sensor high/low limits for SDHM (IssueID=33297) - Fix fan speed control - CPU Ovheat LED control through HWM NCT7904D (IssueID= 33090, 30630) 2. [X9DR6-F] Fix HWM NCT7904D Init (IssueID=33025,30307,33297,32774,33017,33079) 3. Fix iKVM quality poor issue (IssueID=31930,4486) ====================================================================================== Filename: SMT_X9_136.bin ver1.36 Date: 11-22-2011 1. Set the fan speed threshold per Thermal Design Guide as 300, 450, 600(rpm) 2. Make sensor name standard with SuperDoctor, VTT and VDIMM 3. Add PCH sensor 4. [X9DRW+] Fix the missing sensor, +5VSB 5. [X9DRG] Add On Board LAN Temp sensor reading 6. [X9DRD] Correct HWM address as 0x5C (IssueID: 33090, 32645, 32718 & 30599) 7. Fix iKVM alive after the web session close Validation: iKVM console should be timed out as web session close 8. [X9DRT_SG] Set default LAN Interface as Share LAN ====================================================================================== Filename: SMT_X9_135.bin ver1.35 Date: 11-18-2011 1. Bug Fix Operator priviledge can't launch KVM through IPMI GUI (IssusID: 33001) 2. Bug Fix unexpected strings shown on reload IPMI Config page (IssueID: 3926) 3. Bug Fix bridge command through KCS 4. Add PCH temperature reading as Fan Speed Control source for mb using NCT7904D 5. [X9DRG] - Recreate sensor list, and add PCH Temp reading - Bug Fix CPU Temp reading - Adjust fan mode available for X9DRG, and default setting as Optimal Mode. 6. [X9DRT-D-SG007] - Power on/off through HWM 7904D - Report power consumption through LM25066 - Bug fix sensor reading ====================================================================================== Filename: SMT_X9_134.bin ver1.34 Date: 11-14-2011 1. [X9SRI/E] HWM NCT6776F Initialization 2. Enable Inlet Temp reading for motherboards using HWM NCT6776F ====================================================================================== Filename: SMT_X9_133.bin ver1.33 Date: 11-11-2011 1. [X9DRW, X9DRX] Bug fix HWM NCT7904D support 2. [X9DRT] configure sensor high/low limits for SDHM 3. Enable Inlet Temp reading for NM 4. Bug fix security issue on IPMI Configuration & KVM prview snapshot Validation: IPMI Configuration is downloadable by User privilege: 1) save config as Administrator, and then log out 2) login as User 3) save config by the link http://IP-OF-IPMI/cgi/url_redirect.cgi?url_name=save_config.bin&url_type=file KVM preview snapshot can be accessed without authentication http://IP-OF-IPMI/images/Snapshot.bmp ====================================================================================== Filename: SMT_X9_132.bin ver1.32 Date: 11-09-2011 1. Allow Operator access UID control 2. Add hardware monitor NCT7904D support for X9DRW-LN4+, X9DRX 3. Add Node Management support for X9SCA & X9SCM_II *** Required BIOS support 4. Add Device/SSID for X9DRT-SG, X9SRL, X9SCV ====================================================================================== Filename: SMT_X9_131.bin ver1.31 Date: 10-27-2011 1. [X9DR6] Bug fix CPU Temp reading problem (IssueID: 32495, 32594) 2. [X9SRG] Bug fix Fan sensor naming doesn't match with silkscreen (IssueID=32536) 3. [X9DBU] Adjust formula of -12V sensor reading 4. [X9DRL] Correct sensor naming of VDIMM/EFGH & FANA/B (IssueID: 32367) 5. Bug fix Administrator's username visible to Operator privilege at IPMI Web ====================================================================================== Filename: SMT_X9_130.bin ver1.30 Date: 10-19-2011 1. Filter out event logged by Windows 2. [X9SCM/X9SCA] Adjust formula of -12V sensor reading 3. [X9DR6-F] Patched for hardware change rev 1.10 and earlier Note: 1) Fixed IPMB conflict after reading PCH temp(IPMI Rev1.29) 2) Backward compatible for hardware rev 1.10 and earlier, which doesn't support PCH temp to avoid bus hange issue 4. [X9DR6-LN4+, X9DR6-F] Bug fix LED stop blinking when power or fan fail asserted 5. Add new motherboard X9DRL, X9DRH & X9SRG support ====================================================================================== Filename: SMT_X9_129.bin ver1.29 Date: 10-11-2011 1. [X9DR6-LN4+, X9DR6-F] Remove Clear Chassis Intrusion Button from Web for X9 using HWM NCT7904D 2. [X9DR6-LN4+, X9DR6-F] Add PCH and Memory temperature reading as Fan Speed Control source Validation: Please update BIOS with correct setting for PCH Thermal Reading 3. Bug fix undefined "SMTP SSL Auth" from Web ====================================================================================== Filename: SMT_X9_128.bin ver1.28 Date: 10-05-2011 1. Bug fix SOL corrupted display at bios post 2. [X9DR6-LN4+, X9DR6-F] Bug fix Fan Speed Control during Fan Fail asserted 3. [X9DR6-LN4+, X9DR6-F] Bug fix Fan Fail LED doesn't turn on until 10s later or longer ====================================================================================== Filename: SMT_X9_127.bin ver1.27 Date: 09-29-2011 1. [X9DR6-LN4+, X9DR6-F, X9DRT] Bug fix for Hardware monitor(NCT7904D) Init & Fan Speed Control *************************************************** Validation: AC cycle required after firmware update *************************************************** 2. Add new motherboard X9SRW support 3. Bug fix KVM poor quality issue ====================================================================================== Filename: SMT_X9_126.bin ver1.26 Date: 09-26-2011 1. [X9DR6-LN4+, X9DR6-F, X9DRT] Bug fix for Fan Speed Control 2. [X9DR6-F] Filtered out CPU Errors false alarms during on/off test 3. [X9DRT] Corrected sensor name of DIMM Voltage as VDIMM/ABCD and VDIMM/EFGH 4. Allowed Operator full access to KVM, Mouse Mode, and Virtual Media Validation: Operator should be able to change mouse mode, virtual media setting, and access KVM as well ====================================================================================== Filename: SMT_X9_125.bin ver1.25 Date: 09-22-2011 1. [X9DR6-LN4+] Turn on/off Fan Fail LED during fan fail Asserted/De-asserted 2. [X9DR6-LN4+, X9DRT] Bug fix sensor reading during power on/off test *************************************************** Validation: AC cycle required after firmware update *************************************************** 3. [X9DRT] Removed Chassis Intrusion from sensor list ====================================================================================== Filename: SMT_X9_124.bin ver1.24 Date: 09-16-2011 1. Bug fix on HW monitor init Validation: run system on/off test, and check the sensors are reporting correctly 2. Bug fix on Fan Speed Control Validation: 1) change fan mode through Web; Configuration -> Fan Mode 2) Full Speed after fan fail 3. Allowed Operator to change Mouse Mode Validation: log in as an Operator, and change mouse mode through Web; Configuration -> Mouse Mode ====================================================================================== Filename: SMT_X9_123.bin ver1.23 Date: 09-09-2011 1. Support X9DR6-LN4+ using HERMON. 2. Fix the bug of chassis intrusion Short the chassis intrusion jumper on the board, the detection will show in the web. 3. Added keyboard LED patch. Validation: use KVM over the web, and press “Num Lock?to check if LED is respond. 4. Enable Operator to full access of KVM. Validation: virtual media can be accessed by Operator account 5. Add GPU reading temperature for X9DRG. 6. Update Manufacturer I.D. Validation: use ipmitool to check the mc info, and verify the manufacturer ID is 10876 ====================================================================================== Filename: SMT_X9_122.bin ver1.22 Date: 09-02-2011 1. Adjust threshold of OH for X9SCD board. 2. Add sensor list to support additional board, X9DRG. ====================================================================================== Filename: SMT_X9_121.bin ver1.21 Date: 08-29-2011 1. Fix the bug that the virtual temperature is not updated. Thus, fan speed reaction to temperature is functional. 2. Add sensor list to support additional board, X9DRD. ====================================================================================== Filename: SMT_X9_120.bin ver1.20 Date: 08-24-2011 1. Restore Fan Speed setting after Fan Fail recovered NoTE: 1) all the fans are forced to be full-speed during fan fail asserted, 2) as fan fail de-asserted, fan speed control restored as the fan speed mode is. ====================================================================================== Filename: SMT_X9_119.bin ver1.19 Date: 08-23-2011 1. Hardware monitor NCT7904D Initialization 2. [X9DR6/X9DA6/X9DRT] Fan Control ====================================================================================== Filename: SMT_X9_118.bin ver1.18 Date: 08-16-2011 1. [X9SCD] Adjust fan speed according to the fan mode after post 2. Add new motherboard X9DRT support ====================================================================================== Filename: SMT_X9_117.bin ver1.17 Date: 08-10-2011 1. [X9SCD] Add Fan Control ====================================================================================== Filename: SMT_X9_116.bin ver1.16 Date: 08-04-2011 1. [X9SCD] Read CPU Temperature from ME ====================================================================================== Filename: SMT_X9_115.bin ver1.15 Date: 07-29-2011 1. [X9DR6] Read CPU Temperature from ME ====================================================================================== Filename: SMT_X9_114.bin ver1.14 Date: 07-14-2011 1. Bug fix Event Log description undefined from web GUI(IssusID: 30352, 30327 and 30295) Validation: Server Health-> Event Log 2. Bug fix Gateway IP lost Validation: change network setting from static to dhcp by using ipmitool or IPMICFG 3. Add iKVM privilege verification Validation: virtual media can't be accessed by Operator account 4. [X9DA6] add sensor readings ====================================================================================== Filename: SMT_X9_113.bin ver1.13 Date: 06-22-2011 1. Add new motherboard X9DR6 (Support PCHHOT, CPU Error 0/1/2 Event Logs) 2. Bug fix Event Log description undefined from web GUI Validation: Server Health-> Event Log 3. Bug fix sensor status icon missing at webpage header Validation: summarized sensor status icon located at up-right corner of webpage 4. Bug fix unable to delete newly added Users (IssueID=29907) 5. Bug fix Alert Email description of CPU Overheat event (IssueID=29583) 6. Bug fix SMASH login without password ====================================================================================== Filename: SMT_X9_112.bin ver1.12 Date: 06-02-2011 1. Support Circular Buffer evnet logs Description: Event logged as FIFO mechanism when number of logs exceeds the maximum fixed-size, 512 2. Support IP Control Validation: Verify IP Control feature at IPMI Web-> Configuration-> IP Control 3. [X9SCD] Support Power Monitoring from LM25066 National Chip Description: 1. Power Consumption, Input Current & Input Power is monitored at IPMI web-> Miscellaneous-> Power Monitoring 2. Power consumption is reported to ME through 0xE2 command ====================================================================================== Filename: SMT_X9_111.bin ver1.11 Date: 05-26-2011 1. Add "All Event" category as default selection at Event Log page 2. Renew SSL Certificate Validation: 1) enter Web GUI->Configuration->SSL Certificate, and 2) verify the certificate's validity *** Note: Factory Default REQUIRED 3. Change ME slave address to 0x2C in SDR record ====================================================================================== Filename: SMT_X9_110.bin ver1.10 Date: 05-12-2011 1. New feature: launch SOL over SMASH Validation: 1) login IPMI SMASH through SSH, 2) follow the command flow: cd system1 -> cd sol1 -> start Note: only one SOL session can be launched at a time. 2. Improve security for IPMI Configuration backup Validation: Verify the following steps: 1) open IPMI web 2) click on Maintenance -> IPMI Configuration 3) save IPMI configuration at local drive, and 4) check if the configuration can "NOT" be located at http://ipmi-ip-address/save_config.bin 3. Filter out unknown events #0x17 from ME (IssueID=28839) Validation: unknown events #0x17 should be screened out while doing system on/off through IPMI ====================================================================================== Filename: SMT_X9_109.bin ver1.09 Date: 04-29-2011 1. Fix CPU overheat false alarm 2. Add new motherboard X9SCD support ====================================================================================== Filename: SMT_X9_108.bin ver1.08 Date: 04-01-2011 1. Official release for production ====================================================================================== Filename: SMT_X9_107.bin ver1.07 Date: 03-29-2011 1. [X9SCL/M, X9SCA/I] Remove Thermal Trip event log to prevent false alarm 2. Modify default FRU Description:Board Manufacture modified as "Supermicro" and all other entries cleared Note: Required OEM command raw 0x30 0x41(wait for BMC reset) to replace with the new FRU content ====================================================================================== Filename: SMT_X9_106.bin ver1.06 Date: 03-18-2011 1. Fix Alert table blank at the webpage when enter more than 29 characters (IssueID: 95761) Validation: 1. Connect to IPMI by web browser, 2. Go to Configuration -> Alerts and select one entry for modify, 3. In the Message space, enter 30 characters and then save it and then the alert table will be blank. 2. X9SCL/M, X9SCA/I: Support thermal trip event logs ====================================================================================== Filename: SMT_X9_105.bin ver1.05 Date: 03-11-2011 1. X9SRI/E: correct sensor readings ====================================================================================== Filename: SMT_X9_104.bin ver1.04 Date: 02-23-2011 1. Fix KVM issue with UEFI BIOS Validation: reboot system by macro "ctrl+alt+del" and check if key-in is available 2. New feature: Port Configuratioin at Web GUI in Configuration category Description: ports of web, web SSL, IKVM server, virtual media are modifiable through web GUI 3. Fix Gateway setting can't work through different subnets ====================================================================================== Filename: SMT_X9_103.bin ver1.03 Date: 02-09-2011 1. Correct size of video/graphics memory as 16MB *** Note: Requires AC on/off after flashing firmaware 2. Fix cpu temp "Overheat" logged when the reading reports "High" Description: CPU temp Overheat should be logged as the reading reaches "Overheat" 3. For security issue, set the privilege of user ID1(Anonymous) with no access and clear jnlp kvm cache Validation: 1. open IPMI web, 2 click Configuration->Users, and 3 check the privilege of user shows Reserved; 4. launch kvm console, and 5. check if kvm jnlp file is cached after exit ====================================================================================== Filename: SMT_X9_102.bin ver1.02 Date: 02-01-2011 1. Add new motherboard support X9SCA/I 2. Add new motherboard support X9SRI/E ====================================================================================== Filename: SMT_X9SCL_M_V101.bin ver1.01 Date: 01-11-2010 1. Fix KVM slight flashes of white space while screen resolustion is below 800*640 ====================================================================================== Filename: SMT_X9SCL_M_V100.bin ver1.00 Date: 12-30-2010 1. change memory configuration for Hynix 800 memory Note: Please do AC off/on after updating firmware. ====================================================================================== Filename: SMT_218.bin ver2.18 Date: 12-17-2010 1. X9SCL/X9SCM: modify Fan5 to FanA ====================================================================================== Filename: SMT_213.bin ver2.13 Date: 11-10-2010 1. Add new SSID for X9SCM ====================================================================================== Filename: SMT_212.bin ver2.12 Date: 10-25-2010 1. Add new motherboard X9SCL/X9SCM support